EN
CN

Lisong High-Speed Machine Series — Fast Is a System Capability

2026-11-09

      In the injection molding industry, it is not difficult to label a machine’s injection speed above 300 mm/s. What is difficult is maintaining product precision, mold safety, and equipment life while running at high speed. The reason Lisong’s high-speed machine series can establish itself simultaneously in PET, thin-wall packaging, buckets, and other fields is not a single impressive parameter, but a complete set of system capabilities built around “high-speed precision.”

The Premise of High Speed: Clamping Must Be Stable

      The faster the injection speed, the greater the impact of the melt on the mold. If the clamping structure lacks rigidity, the platens will produce slight displacement during high-pressure filling, causing flash, uneven wall thickness, and even damage to the mold parting surface.

      Lisong takes two routes in clamping structure. PET preform systems use direct-pressure clamping, where a large-diameter cylinder directly pushes the platen along the central axis, and the clamping force spreads evenly from the center outward. The platen experiences balanced force, with deformation controlled at the micron level. Thin-wall packaging and bucket high-speed machines use mechanical direct-pressure clamping, which also eliminates the hinge pins and bronze bushes of traditional toggle mechanisms and relies on direct cylinder drive combined with low-friction linear guide rails. There is no hinge pin wear, the clamping force does not decay, and factory precision is maintained under high-frequency mold opening and closing.

      Two routes, one logic: the clamping force must be uniform, stable, and repeatable over the long term.

The Guarantee of High Speed: Enlarged and Thickened Tie Bars and Platens

      High-speed operation means greater mechanical stress and more frequent reciprocating motion. The tie bars and platens of Lisong’s entire high-speed machine series are enlarged and thickened. A larger tie bar cross-sectional area provides higher tensile strength, and thicker platens provide stronger resistance to deformation. Clamping rigidity is therefore greatly improved. The machine does not shake or deviate during high-speed operation, and both product consistency and mold life are guaranteed.

The Drive of High Speed: Electric Storage as Standard

      Traditional hydraulic storage responds slowly and consumes high energy, easily becoming a bottleneck in high-cycle production. Lisong’s entire high-speed machine series comes standard with electric storage, with servo motors directly driving the storage action. Response speed is fast, storage time is short, and the injection screw can return to the ready-to-inject position more quickly. At the same time, servo motors do work on demand, with energy consumption far lower than hydraulic storage. Faster storage means a faster overall cycle; lower energy consumption means lower long-term operating costs.

The Source of High Speed: Dedicated Design of Screw and Injection Unit

      Different application scenarios have completely different requirements for screws. PET materials are sensitive to thermal history and require low-temperature, low-shear plasticization. Lisong’s PET screws are optimized for this characteristic in terms of length-to-diameter ratio and mixing section, ensuring uniform melt temperature and low acetaldehyde generation. Thin-wall packaging pursues high plasticizing efficiency and high mixing uniformity, and the screw design emphasizes rapid melting and stable conveying. Bucket products have relatively large wall thickness, and the screw needs to balance plasticizing capacity and injection pressure.

      In terms of the injection unit, the structure of Lisong’s high-speed machines has been reinforced to maintain rigid stability during high-frequency reciprocating motion. With servo drive, the injection unit response reaches the millisecond level, and injection speed switching is precise and controllable.

The Auxiliary of High Speed: Infrared Heating Coils

      The use of infrared heating coils allows raw material to reach the molten state faster in the barrel. Infrared radiation acts directly on the barrel surface, and heat transfer efficiency is higher than traditional resistance heating. Plasticization time is shortened, preparing sufficient melt for high-speed injection. At the same time, infrared heating consumes less energy, offering better long-term operating economy.

      The core logic of Lisong’s high-speed machine series is not complicated: injection speed must be high, clamping must be stable, storage must be fast, heating must be efficient, and structure must be rigid. When every link is in place, high speed is not a fleeting parameter, but a production capability delivered stably day after day.